Skip to main content
Installation
AEG Support

Installation

icon-warning.pngWarning
Refer to Safety chapters.

Location of the appliance

You can install your freestanding appliance with cabinets on one or two sides and in the corner.

icon-info.pngKeep a distance of about 1 cm between the appliance and the back wall to make sure that the lid opens.

For minimal distances for fitting check the table.

GUID-DFCA9FA6-8484-46BE-8311-199AEB79D9A4-preview_v1.png
Minimum distances

Dimension

mm

A

400

B

650

C

150

Technical data

Voltage

230 V

Frequency

50 Hz

Appliance class

1

Dimension

mm

Height

855

Width

600

Depth

600

Other technical data

Appliance category:

II2E+3+

Gas original:

G20/G25 (2E+) 20/25 mbar

Gas replacement:

G30 (3+) 28-30 mbar

G31 (3+) 37 mbar

Bypass diameters

BURNER

Ø BYPASS1) 1/100 mm

Auxiliary

29 / 30

Semi-rapid

32

Triple Crown

67

1) Type of bypass depends on model.

Gas burners for NATURAL GAS G20 20 mbar

BURNER

NORMAL POWER kW

REDUCED POWER kW

INJECTOR MARK 1/100 mm

Triple Crown

4.0

1.80

146

Semi-rapid

2.0 / 1.91)

0.43 / 0.451)

96

Auxiliary

1.0

0.35

70

1) Type of bypass depends on model.

Gas burners for NATURAL GAS G25 25 mbar

BURNER

NORMAL POWER kW

REDUCED POWER kW

INJECTOR MARK 1/100 mm

Triple Crown

3.8

1.7

146

Semi-rapid

2.0 / 1.751)

0.43 / 0.451)

96

Auxiliary

0.95 / 0.91)

0.35

70

1) Type of bypass depends on model.

Gas burners for LPG G30 28-30 mbar

BURNER

NORMAL POWER kW

REDUCED POWER kW

INJECTOR MARK 1/100 mm

NOMINAL GAS FLOW g/h

Triple Crown

4.0

1.80

101

290.85

Semi-rapid

2.0

0.43

71

145.43

Auxiliary

1.0

0.35

50

72.71

Gas burners for LPG G31 37 mbar

BURNER

NORMAL POWER kW

REDUCED POWER kW

INJECTOR MARK 1/100 mm

NOMINAL GAS FLOW g/h

Triple Crown

4.0

1.8

101

285.66

Semi-rapid

2.0

0.43

71

142.83

Auxiliary

1.0

0.35

50

71.41

Gas connection

Use a fixed connections or use a flexible stainless steel pipes in compliance with the regulation in force. If you use flexible metallic pipes, make sure they do not come in touch with mobile parts and they are not squeezed.


GUID-ED0A23A8-6187-46BB-89F5-FEEBCBAC178C-preview_v1.png
icon-warning.pngWarning
The gas connection pipe must not touch the part of the appliance shown in the illustration.

Flexible nonmetal pipes connection

If you have an easy access to the connection, you can use a flexible pipe. The flexible pipe must be tightly attached by clamps.

In installation always use the pipe holder and the gasket. The flexible pipe can be applied when:

  • it can not get hotter than room temperature, higher than 30 °C,

  • it is not longer than 1500 mm,

  • it has no narrowing anywhere,

  • it is not twisted or tighten,

  • it does not get in touch with sharp edges or corners,

  • it's conditions can be easily checked.

When checking the flexible pipe make sure:

  • it does not show cracks, cuts, marks of burnings on the two ends and on its full length,

  • the material is not hardened, but shows its correct elasticity,

  • the fastening clamps are not rusted,

  • expired term is not due.

If one or more defects are visible, do not repair the pipe, but replace it.

icon-warning.pngWarning
When installation is complete, make sure that the seal of each pipe fitting does not leak. To check the seal use a soap solution, not a flame.

The gas supply ramp is on the rear side of the control panel.

icon-warning.pngWarning
Before you connect the gas, disconnect the appliance from the electricity supply or switch off the fuse in the fuse box. Close the primary valve of the gas supply.

Adjustment to different types of gas

icon-info.png Let only an authorized person do the adjustment to different types of gas.
icon-info.png If the appliance is set for natural gas you can change it to liquid gas, with the correct injectors. The gas rate is adjusted to suit.
icon-warning.pngWarning
Before you replace the injectors, make sure that the gas knobs are in the Off position. Disconnect the appliance from the electrical supply. Let the appliance cool down. There is a risk of injury.
icon-info.png The appliance is set to default gas. To change the setting always use the gasket sealing.

GUID-C7DD4F0A-1616-45D2-9778-759A0F0F1FBB-preview_v2.png
  1. Gas connection point (only one point is applicable for the appliance)

  2. Gasket

  3. Adjustable connection

  4. LPG pipe holder

Hob injectors replacement

Replace the injectors when you change the gas type.

  1. Remove the pan supports.
  2. Remove the caps and crowns of the burner.
  3. Remove the injectors with a socket spanner 7.
  4. Replace injectors with the ones necessary for the type of gas you use.
    GUID-428F2655-DCEE-4F00-9A79-A90B507D21FD-preview_v1.png
  5. Replace the rating plate (it is near the gas supply pipe) with the one for the new type of gas supply.
    icon-info.png You can find this plate in the bag supplied with the appliance.

If the supply gas pressure is not constant or it is different from the necessary pressure, install an applicable pressure adjuster on the gas supply pipe.

Adjusting the minimum gas level on the hob burner

  1. Disconnect the appliance from the electricity.
  2. Remove the knob for the hob.
    If there is no access to the bypass screw dismount the control panel before adjustment start.
  3. With a thin and flat screwdriver adjust the bypass screw A.

    The model determines the position of the bypass screw A.



    GUID-435578F4-AF50-4D7E-9DF2-81106D685FCD-preview_v3.png

Changing from natural gas to liquid gas

  1. Fully tighten the bypass screw.
  2. Put the knob back.

Changing from liquid gas to natural gas

  1. Unscrew approximately one turn the bypass screw position A.
  2. Put the knob for the hob back.
  3. Connect the appliance to the electricity.
    icon-warning.pngWarning
    Put the mains plug into the mains socket only if all parts are back into their initial position. There is a risk of injury.
  4. Light the burner.

    Refer to "Hob - Daily use" chapter.

  5. Turn the knob for the hob to the minimum position.
  6. Remove the knob for the hob again.
  7. Screw on slowly the bypass screw till the flame becomes minimum and stable.
  8. Put the knob for the hob back on.

Levelling of the appliance


GUID-FDCAEDC7-0922-4FE2-9F42-0D4D5456E3E6-preview_v1.png

Use small feet on the bottom of appliance to set the appliance top surface level with other surfaces.

Anti-tilt protection

Set the correct height and area for the appliance before you attach the anti-tilt protection.

icon-warning.pngCAUTION
Make sure you install the anti-tilt protection at the correct height.
icon-info.png Make sure that the surface behind the appliance is smooth.

You must install the anti-tilt protection. If you do not install it, the appliance can tilt.

Your appliance has the symbol shown on the picture (if applicable) to remind you about the installation of the anti-tilt protection.


GUID-BDE9C6AA-509E-42DF-AF86-4BEFA0B68B5D-preview_v1.png

GUID-13691040-4EC5-4487-BC44-00EF99B5EB83-preview_v1.png
  1. Install the anti-tilt protection 232 - 237 mm down from the top surface of the appliance and 110 - 115 mm from the side of the appliance into the circular hole on a bracket. Screw it into the solid material or use applicable reinforcement (wall).

    GUID-5191C45A-B3B2-4642-8D91-5C62736DCBA8-preview_v1.png
  2. You can find the hole on the left side at the back of the appliance. Lift the front of the appliance and put it in the middle of the space between the cupboards. If the space between the bench cupboards is larger than the width of the appliance, you must adjust the side measurement to centre the appliance.
icon-info.png If you changed the dimensions of the cooker, you must align the non-tip device correctly.
icon-warning.pngCAUTION
If the space between the bench cupboards is larger than the width of the appliance, you must adjust the side measurement to the centre of the appliance.

Electrical installation

icon-warning.pngWarning
The manufacturer is not responsible if you do not follow the safety precautions from Safety chapters.

This appliance is supplied with a main plug and a main cable.

icon-warning.pngWarning
The power cable must not touch the part of the appliance shown in the illustration.

GUID-6CE0AFE4-371B-4AC9-A571-674CCFD98A7E-preview_v1.png
  • Was this article helpful?