Skip to main content
Oven - Care and cleaning
AEG Support

Oven - Care and cleaning

icon-warning.pngWarning
Refer to Safety chapters.

Notes on cleaning

  • Clean the front of the appliance with a soft cloth with warm water and a cleaning agent.

  • To clean metal surfaces, use a usual cleaning agent.

  • Clean the appliance interior after each use. Fat accumulation or other food remains may result in a fire. The risk is higher for the grill pan.

  • Clean stubborn dirt with a special oven cleaner.

  • Clean all accessories after each use and let them dry. Use a soft cloth with warm water and a cleaning agent.

  • If you have nonstick accessories, do not clean them using aggressive agents, sharp-edged objects or a dishwasher. It can cause damage to the nonstick coating.

Stainless steel or aluminium appliances

icon-info.png Clean the oven door with a wet sponge only. Dry it with a soft cloth. Do not use steel wool, acids or abrasive materials as they can damage the oven surface. Clean the oven control panel with the same precautions.

Removing the shelf supports

To clean the oven, remove the shelf supports.

  1. Pull the front of the shelf support away from the side wall.

    GUID-371FD560-D901-49FE-85A6-49428EB7B0B4-preview_v1.png
  2. Pull the rear end of the shelf support away from the side wall and remove it.

    GUID-CD158F8A-80F7-4C67-96EF-24215A0CC915-preview_v1.png

Install the shelf supports in the opposite sequence.

Removing and installing the oven glass panels

You can remove the internal glass panels to clean it. The number of glass panels is different for different models.

icon-warning.pngWarning
Keep the oven door slightly open during the cleaning process. When you open it fully it may accidentally close causing potential damage.
icon-warning.pngWarning
Do not use the appliance without the glass panels.
  1. Open the door until it is at an angle of approximately 30°. The door stands alone when slightly open.

    GUID-652BBE47-1FC8-46D0-867C-72929011153C-preview_v1.png
  2. Hold the door trim (B) at the top edge of the door on both sides and push inwards to release the clip seal.

    GUID-3D51A84A-A226-4FF6-A2BC-D659E7024E47-preview_v1.png

  3. Pull the door trim to the front to remove it.
    icon-warning.pngWarning
    When you take out the glass panels the oven door tries to close.
  4. Hold the top edge of the door glass panels and pull them up one by one.
  5. Clean the glass panel with water and soap. Dry the glass panel carefully.

When the cleaning is complete, install the glass panels and the oven door. Do the above steps in the opposite sequence. Install the smaller panel first, then the larger.

icon-warning.pngCAUTION
The screen with a printing on the inner glass panel must face the inner side of the door.
icon-warning.pngCAUTION
Make sure that after installation the surface of the frame of the glass panel on the screen with a printing is not rough when you touch it.
icon-warning.pngCAUTION
Make sure that you install the internal glass panel in the appropriate seats.

Removing the drawer

icon-warning.pngWarning
Do not keep flammable items (such as cleaning materials, plastic bags, oven gloves, paper or cleaning sprays) in the drawer. When you use the oven, the drawer can become hot. There is a risk of fire.

The drawer below the oven can be removed for cleaning.

  1. Pull the drawer out until it stops.

    GUID-670A52F4-6A8E-456B-9924-621A58C73799-preview_v1.png
  2. Slowly lift the drawer.
  3. Pull the drawer out fully.

To install the drawer, do the above steps in the opposite sequence.

Replacing the lamp

Put a cloth on the bottom of the interior of the appliance. It prevents damage to the lamp glass cover and the cavity.

icon-warning.pngWarning
Danger of electrocution! Disconnect the fuse before you replace the lamp. The lamp and the lamp glass cover can be hot.
  1. Deactivate the appliance.
  2. Remove the fuses from the fuse box or deactivate the circuit breaker.

The back lamp

  1. Turn the lamp glass cover counterclockwise to remove it.
  2. Clean the glass cover.
  3. Replace the lamp with a suitable 300 °C heat-resistant lamp.
  4. Install the glass cover.
  • Was this article helpful?